View ML6209_8110455.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

p1/14 rev. a, march 2006 ML6209 ML6209 series - high speed ldo regulators (low esr capacitor compatible, on/off switch) features maximum output current : 150ma dropout voltage : 200mv (iout = 100ma) maximum operating voltage : 10v output voltage range : 1.5v ~ 6.0v in 50mv increments highly accurate : 2% low power consumption : typ 25a standby current : less than 0.1a high ripple rejection : 70db (10 khz) low output noise : 30vrms operational temperature range : -40c ~ +85c low esr capacitor compatible : ceramic capacitor applications mobile phones cordless phones cameras, video recorders portable games portable av equipment reference voltage battery-powered equipment cmos low power consumption dropout voltage: 60mv @ 30ma, 200mv @ 100ma maximum output current: 150ma highly accurate: 1.5v ~ 1.95v 3% 2.0v ~ 6.00v 2% output voltage range: 1.5v ~ 6.0v low esr capacitor compatible general description the ML6209 series are highly precise, low noise, po sitive voltage ldo regulators manufactured using cmos process. the ser ies achieves high ripple rejection and low dropout and consists of a standard voltage source, an error correction, current limiter and a phase compensation circuit plus a driver transistor. output voltage is selectable in 50mv increments within a range of 1.5v ~ 6.0v. the series is also compatible with low esr ceramic capacitors which give added output stability. this stability can be maint ained even during load fluctuations due to the excellent transient respons e of the series. the ce function enables the output to be turned off, resul ting in greatly reduced power consumption. typical application
p2/14 rev. a, march 2006 ML6209 product classification selection guide the following options for the ce pin logic and internal pull-up/down are available: active 'high' + no pull-down resistor built-in (standard) active 'high' + 800k pull-down resistor built-in (semi-custom) active 'low' + no pull-up resistor built-in (semi-custom) active 'low' + 800k pull-up resistor built-in (semi-custom) note: *with the pull-up resistor or pull-down resis tor built-in types, the supply current during opera tion will increase by vin / 800kg (typ.) ordering information ML6209 1234567 designator symbol description a active ?high? (pull-down resistor built in) b active ?high? (no pull-down resistor built in) c active ?low? (pull-up resistor built in) 1 d active ?low? (no pull-up resistor built in) 23 15 ~ 60 output voltage: e.g. 20 ? 2.0v, 30 ? 3.0v etc. 2 output voltage: 100mv increments, 2% accuracy e.g. 2 =3, 3 =8, 4 =2 ? 3.8v, 2% 4 a output voltage: 50mv increments, 2% accuracy e.g. 2 =3, 3 =8, 4 =a ? 3.85v, 2% m sot-23-5 package 5 p sot-89-5 package r embossed tape: standard feed 6 l embossed tape: reverse feed 7 g lead-free package please note that ?b? version is the standard part while the a, c and d are semi-custom parts. pin assignment sot-23-5 sot-89-5 pin function pin no. sot-23-5 sot-89-5 pin name description 1 4 vin input 2 2 vss ground 3 3 ce on/off control 4 1 n.c. no connection 5 5 vout output
p3/14 rev. a, march 2006 ML6209 marking information sot-23-5 (top view) sot-89-5 (top view) 1 represents the product name designator product name p ML6209******* 2 represents the integer part of the output voltage designator output voltage (v) 1 1.0 2 2.0 3 3.0 4 4.0 5 5.0 6 6.0 3 represents the decimal part of the output voltage designator output voltage (v) designator output voltage (v) 0 0.0 a 0.05 1 0.1 b 0.15 2 0.2 c 0.25 3 0.3 d 0.35 4 0.4 e 0.45 5 0.5 f 0.55 6 0.6 g 0.65 7 0.7 h 0.75 8 0.8 i 0.85 9 0.9 j 0.95 e.g. 23 =12 ? 1.20v and 23 =1c ? 1.25v. 4 represents the resistor version designator resistor version a active ?high? (pull-down resistor built in) b active ?high? (no pull-down resistor built in) c active ?low? (pull-up resistor built in) d active ?low? (no pull-up resistor built in)
p4/14 rev. a, march 2006 ML6209 package information sot-23-5
p5/14 rev. a, march 2006 ML6209 package information sot-89-5
p6/14 rev. a, march 2006 ML6209 block diagram the diodes in the circuit above are the protective dio des. absolute maximum ratings parameter symbol ratings units input voltage vin 10 v output current iout 400 ma output voltage vout vss-0.3 ~ vin+0.3 v power dissipation sot25 pd 250 mw operation ambient temperature topr -40 ~ +70 ?c storage temperature tstg -55 ~ +80 ?c * iout= the range of pd/ vin-vout
p7/14 rev. a, march 2006 ML6209 electrical characteristics ML6209a, b series ta=25 c -40 c ? ta ? 85 c parameter symbol conditions min typ max min typ max units circuit i out = 30ma, 1.5v v out (t) 1.95v x0.97 v out (t) x1.03 x0.96 v out (t) x1.04 output voltage v out (e) i out = 30ma, 2.0v v out (t) 6.0v x0.98 v out (t) x1.02 x0.97 v out (t) x1.03 v 1 maximum output current i out max 150 150 ma 1 load regulation ? v out 1ma i out 100ma 15 50 30 80 mv 1 vdif1 i out = 30ma e-1 mv dropout voltage vdif2 i out = 100ma e-2 mv 1 supply current (a series) v in =v ce =v out (t)+1.0v 20 25 40 20 28 44 supply current (b series) i dd v in =v ce =v out (t)+1.0v 20 25 40 20 28 44 a 2 standby current istby v in =out(t)+1.0v, vce=vss 0.01 0.10 0.05 1.00 a 2 line regulation ? v out ? v in -v out v out (t)+1.0v v in 10v i out =30ma 0.01 0.20 0.05 0.30 %/v 1 input voltage v in 2 10 2 10 v -- output voltage temp. characteristics ? v out ? topr-v out i out =30ma -40 c topr 85 c 100 ppm/ c 1 output noise en i out =10ma 300hz ~ 50khz 30 vrms 3 ripple rejection rate psrr v in =[v out (t)+1.0]v+1.0vp-p ac i out =50ma, f=10khz 70 db 4 current limited iiim v in =v out (t)+1.0v, v ce =v in 300 280 ma 1 short-circuit current ishort v in =v out (t)+1.0v, v ce =v in 50 60 ma 1 ce high voltage v ceh 1.6 v in 1.7 v in v 1 ce low voltage v cel 0.25 0.20 v 1 ce high current (a series) i ceh v in =v ce =v out (t)+1.0v -0.10 20 -0.15 25 a 2 ce high current (b series) i ceh v in =v ce =v out (t)+1.0v -0.10 0.10 -0.15 0.15 a 2 ce low current i cel v in =v out (t)+1.0v, v ce =v ss -0.10 0.10 -0.15 0.15 a 2 note (note 1) unless otherwise stated, v in =v out (t) +1.0v (note 2) v out (t)=specified output voltage (note 3) v out (e)=effective output voltage (i.e. the output volta ge when v out (t)+1.0v is provided at the v in pin while maintaining a certain i out value) (note 4) vdif= (v in1 (note6) C v out1 (note5) ) (note 5) v out1 =a voltage equal to 98% of the output voltage whene ver an amply stabilized i out (v out (t)+1.0v) is input. (note 6) v in1 =the input voltage when v out1 appears as input voltage is gradually decreased. (note 7) the values for -40 c topr 85 c are designed values.
p8/14 rev. a, march 2006 ML6209 ML6209c, d series ta=25 c -40 c ? ta ? 85 c parameter symbol conditions min typ max min typ max units circuit i out = 30ma, 1.5v v out (t) 1.95v x0.97 v out (t) x1.03 x0.96 v out (t) x1.04 output voltage v out (e) i out = 30ma, 2.0v v out (t) 6.0v x0.98 v out (t) x1.02 x0.97 v out (t) x1.03 v 1 maximum output current i out max 150 150 ma 1 load regulation ? v out 1ma i out 100ma 15 50 30 80 mv 1 vdif1 i out = 30ma e-1 mv dropout voltage vdif2 i out = 100ma e-2 mv 1 supply current (c series) v in = v out (t) +1.0v, v ce =vss 20 25 40 20 28 44 supply current (b series) i dd v in = v out (t) +1.0v, v ce =vss 20 25 40 20 28 44 a 2 standby current istby v in =vce=out(t)+1.0v 0.01 0.10 0.05 1.00 a 2 line regulation ? v out ? v in -v out v out (t)+1.0v v in 10v i out =30ma 0.01 0.20 0.05 0.30 %/v 1 input voltage v in 2 10 2 10 v -- output voltage temp. characteristics ? v out ? topr-v out i out =30ma -40 c topr 85 c 100 ppm/ c 1 output noise en i out =10ma 300hz ~ 50khz 30 vrms 3 ripple rejection rate psrr v in =[v out (t)+1.0]v+1.0vp-p ac i out =50ma, f=10khz 70 db 4 current limited iiim v in =v out (t)+1.0v, v ce =v ss 300 280 ma 1 short-circuit current ishort v in =v out (t)+1.0v, v ce =v ss 50 60 ma 1 ce high voltage v ceh 1.6 v in 1.7 v in v 1 ce low voltage v cel 0.25 0.20 v 1 ce high current i ceh v in =v ce =v out (t)+1.0v -0.10 0.10 -0.15 0.15 a 2 ce low curr ent (c series) i cel v in =v out (t)+1.0v, v ce =v ss -20 0.10 -25 0.15 a 2 ce low current (d series) i cel v in =v out (t)+1.0v, v ce =v ss -0.10 0.10 -0.15 0.15 a 2 note (note 1) unless otherwise stated, v in =v out (t) +1.0v (note 2) v out (t)=specified output voltage (note 3) v out (e)=effective output voltage (i.e. the output volta ge when v out (t)+1.0v is provided at the v in pin while maintaining a certain i out value) (note 4) vdif= (v in1 (note6) C v out1 (note5) ) (note 5) v out1 =a voltage equal to 98% of the output voltage whene ver an amply stabilized i out (v out (t)+1.0v) is input. (note 6) v in1 =the input voltage when v out1 appears as input voltage is gradually decreased. (note 7) the values for -40 c topr 85 c are designed values.
p9/14 rev. a, march 2006 ML6209 dropout voltage C table 1 symbol e-0 e-1 e-2 dropout voltage 1 (mv) (i out =30ma) dropout voltage 2 (mv) (i out =100ma) parameter output voltage output voltage (v) ta=25 c -40 c topr 85 c ta=25 c -40 c topr 85 c vout vdif1 vdif1 vdif1 vdif1 vdif2 vdif2 vdif2 vdif2 vout(t) min max typ max typ max typ max typ max 1.50 1.455 1.545 400 500 410 520 600 800 620 820 1.55 1.504 1.597 400 500 410 520 600 800 620 820 1.60 1.552 1.648 300 380 310 400 500 680 520 700 1.65 1.601 1.700 300 380 310 400 500 680 520 700 1.70 1.649 1.751 250 320 260 330 400 620 420 640 1.75 1.698 1.803 250 320 260 330 400 620 420 640 1.80 1.746 1.854 200 250 210 260 350 480 360 500 1.85 1.795 1.906 200 250 210 260 350 480 360 500 1.90 1.843 1.957 140 180 150 190 320 460 340 480 1.95 1.892 2.009 140 180 150 190 320 460 340 480 2.00 1.960 2.040 100 150 110 160 270 420 290 440 2.05 2.009 2.091 100 150 110 160 270 420 290 440 2.10 2.058 2.142 100 150 110 160 250 400 280 410 2.15 2.107 2.193 100 150 110 160 250 400 280 410 2.20 2.156 2.244 100 150 110 160 250 400 280 410 2.25 2.205 2.295 100 150 110 160 250 400 280 410 2.30 2.254 2.346 100 150 110 160 240 380 280 400 2.35 2.303 2.397 100 150 110 160 240 380 280 400 2.40 2.352 2.448 100 150 110 160 240 380 280 400 2.45 2.401 2.499 100 150 110 160 240 380 280 400 2.50 2.450 2.550 90 120 100 130 230 350 260 380 2.55 2.499 2.601 90 120 100 130 230 350 260 380 2.60 2.548 2.652 90 120 100 130 230 350 260 380 2.65 2.597 2.703 90 120 100 130 230 350 260 380 2.70 2.646 2.754 90 120 100 130 230 350 260 380 2.75 2.695 2.805 90 120 100 130 230 350 260 380 2.80 2.744 2.856 90 120 100 130 220 330 260 370 2.85 2.793 2.907 90 120 100 130 220 330 260 370 2.90 2.842 2.958 90 120 100 130 220 330 260 370 2.95 2.891 3.009 90 120 100 130 220 330 260 370 3.00 2.940 3.060 80 100 90 110 220 300 260 350 3.05 2.989 3.111 80 100 90 110 220 300 260 350 3.10 3.038 3.162 80 100 90 110 200 280 240 330 3.15 3.087 3.213 80 100 90 110 200 280 240 330 3.20 3.136 3.264 80 100 90 110 200 280 240 330
p10/14 rev. a, march 2006 ML6209 dropout voltage C table 2 symbol e-0 e-1 e-2 dropout voltage 1 (mv) (i out =30ma) dropout voltage 2 (mv) (i out =100ma) parameter output voltage output voltage (v) ta=25 c -40 c topr 85 c ta=25 c -40 c topr 85 c v out vdif1 vdif1 vdif1 vdif1 vdif2 vdif2 vdif2 vdif2 v out (t) min max typ max typ max typ max typ max 3.25 3.185 3.315 80 100 90 110 200 280 240 330 3.30 3.234 3.366 80 100 90 110 200 280 240 330 3.35 3.283 3.417 80 100 90 110 200 280 240 330 3.40 3.332 3.468 80 100 90 110 200 280 240 330 3.45 3.381 3.519 80 100 90 110 200 280 240 330 3.50 3.430 3.570 80 100 90 110 200 280 240 330 3.55 3.479 3.621 80 100 90 110 200 280 240 330 3.60 3.528 3.672 80 100 90 110 200 280 240 330 3.65 3.577 3.723 80 100 90 110 200 280 240 330 3.70 3.626 3.774 80 100 90 110 200 280 240 330 3.75 3.675 3.825 80 100 90 110 200 280 240 330 3.80 3.724 3.876 80 100 90 110 200 280 240 330 3.85 3.773 3.927 80 100 90 110 200 280 240 330 3.90 3.822 3.978 80 100 90 110 200 280 240 330 3.95 3.871 4.029 80 100 90 110 200 280 240 330 4.00 3.920 4.080 70 90 80 100 180 260 220 310 4.05 3.969 4.131 70 90 80 100 180 260 220 310 4.10 4.018 4.182 70 90 80 100 180 260 220 310 4.15 4.067 4.233 70 90 80 100 180 260 220 310 4.20 4.116 4.284 70 90 80 100 180 260 220 310 4.25 4.165 4.335 70 90 80 100 180 260 220 310 4.30 4.214 4.386 70 90 80 100 180 260 220 310 4.35 4.263 4.437 70 90 80 100 180 260 220 310 4.40 4.312 4.488 70 90 80 100 180 260 220 310 4.45 4.361 4.539 70 90 80 100 180 260 220 310 4.50 4.410 4.590 70 90 80 100 180 260 220 310 4.55 4.459 4.641 70 90 80 100 180 260 220 310 4.60 4.508 4.692 70 90 80 100 180 260 220 310 4.65 4.557 4.743 70 90 80 100 180 260 220 310
p11/14 rev. a, march 2006 ML6209 dropout voltage C table 3 symbol e-0 e-1 e-2 dropout voltage 1 (mv) (i out =30ma) dropout voltage 2 (mv) (i out =100ma) parameter output voltage output voltage (v) ta=25 c -40 c topr 85 c ta=25 c -40 c topr 85 c v out vdif1 vdif1 vdif1 vdif1 vdif2 vdif2 vdif2 vdif2 v out (t) min max typ max typ max typ max typ max 4.70 4.606 4.794 70 90 80 100 180 260 220 310 4.75 4.655 4.845 70 90 80 100 180 260 220 310 4.80 4.704 4.896 70 90 80 100 180 260 220 310 4.85 4.753 4.947 70 90 80 100 180 260 220 310 4.90 4.802 4.998 70 90 80 100 180 260 220 310 4.95 4.851 5.049 70 90 80 100 180 260 220 310 5.00 4.900 5.100 50 80 60 90 160 240 200 290 5.05 4.949 5.151 50 80 60 90 160 240 200 290 5.10 4.998 5.202 50 80 60 90 160 240 200 290 5.15 5.047 5.253 50 80 60 90 160 240 200 290 5.20 5.096 5.304 50 80 60 90 160 240 200 290 5.25 5.145 5.355 50 80 60 90 160 240 200 290 5.30 5.194 5.406 50 80 60 90 160 240 200 290 5.35 5.243 5.457 50 80 60 90 160 240 200 290 5.40 5.292 5.508 50 80 60 90 160 240 200 290 5.45 5.341 5.559 50 80 60 90 160 240 200 290 5.50 5.390 5.610 50 80 60 90 160 240 200 290 5.55 5.439 5.661 50 80 60 90 160 240 200 290 5.60 5.488 5.712 50 80 60 90 160 240 200 290 5.65 5.537 5.763 50 80 60 90 160 240 200 290 5.70 5.586 5.814 50 80 60 90 160 240 200 290 5.75 5.635 5.865 50 80 60 90 160 240 200 290 5.80 5.684 5.916 50 80 60 90 160 240 200 290 5.85 5.733 5.967 50 80 60 90 160 240 200 290 5.90 5.782 6.018 50 80 60 90 160 240 200 290 5.95 5.831 6.069 50 80 60 90 160 240 200 290 6.00 5.880 6.120 50 80 60 90 160 240 200 290
p12/14 rev. a, march 2006 ML6209 typical performance characteristics (1) output voltage vs output current (2) output voltage vs input voltage 10 ma 30 ma 100 ma
p13/14 rev. a, march 2006 ML6209
p14/14 rev. a, march 2006 ML6209 (3) supply current vs input voltage disclaimer: the information presented in this document does not form part of any quotation or contract, is believe d to be accurate and reliable and may be changed without notice. no liab ility will be accepted by the publisher for any con sequence of its use.

▲Up To Search▲

Price & Availability of ML6209

	To Download ML6209 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .